1. Operators pre-job, must be job training, familiar with the equipment manual, to understand the structural performance of the machine. Flange drill
2. Jinan Fute CNC numerical control machinery production of CNC angle steel wire structure performance is more complex, and is a large and expensive equipment, should be someone, post, may not undocumented operation.
3. The angle steel wire computer automatic control, the operator should be strictly according to the operating instructions.
4. This angle steel bar is strictly prohibited pressure below 0.35Mpa, the oil temperature is higher than 65 ℃ boot, oil temperature above 45 ℃, should start cooling water cooling system.
5. The operator in the machine work, do not stay away from their jobs, because of special circumstances need to stay away from the machine, should be shut down, cut off the power.
6. The machine in the course of their work, should promptly eliminate the waste head, beans, the machine is blocked, affecting the normal work of the machine.
7. In the work or adjustment of the machine, it is forbidden to approach the loading frame, and the non-operating staff should not be allowed to enter the working frame of the material frame (blank frame, finished material frame).
8. When there is a blank on the feeding road, it is forbidden to turn on the turning device. When the CNC car is in the jig feeding or the clamp bar is withdrawn from the main body, it is forbidden to press the clamp to lift the button. When the CNC car retracts, Do not press the clamp down button in the middle. Flange drill
9. This machine is working, it is forbidden to pass from the front of the safety bar, there is no special circumstances, it is forbidden to lift the front safety bar of the shearing machine, it is absolutely forbidden to pass the safety bar without lifting.
10. The angle of the line in the adjustment of replacement prefix, the word box, punch, die, shear blade, adjust the blade clearance, the guardian must be provided, no person pressing the button.
11. The local hydraulic system (factory) valves have been adjusted, if adjustments need to be adjusted by professionals.
12. The pressure of the hydraulic system should be regularly replaced according to regulations, non-filtered oil into the tank is strictly prohibited.
13. It is forbidden to insert the private tape disk into the drive to avoid bringing the computer virus into the computer.
14. Shear blade, punch die frame, print carriage and moving parts, each time before cleaning with N46 mechanical oil lubrication.
15. Perforated guide rail and screw each class main oil once, the transmission rack and measuring rack and measuring racks to be coated with lubricating grease often lubricated.
16. At get off work, you must cut off the power, clean the equipment dust, clean the venue. Flange drill
2. Jinan Fute CNC numerical control machinery production of CNC angle steel wire structure performance is more complex, and is a large and expensive equipment, should be someone, post, may not undocumented operation.
3. The angle steel wire computer automatic control, the operator should be strictly according to the operating instructions.
4. This angle steel bar is strictly prohibited pressure below 0.35Mpa, the oil temperature is higher than 65 ℃ boot, oil temperature above 45 ℃, should start cooling water cooling system.
5. The operator in the machine work, do not stay away from their jobs, because of special circumstances need to stay away from the machine, should be shut down, cut off the power.
6. The machine in the course of their work, should promptly eliminate the waste head, beans, the machine is blocked, affecting the normal work of the machine.
7. In the work or adjustment of the machine, it is forbidden to approach the loading frame, and the non-operating staff should not be allowed to enter the working frame of the material frame (blank frame, finished material frame).
8. When there is a blank on the feeding road, it is forbidden to turn on the turning device. When the CNC car is in the jig feeding or the clamp bar is withdrawn from the main body, it is forbidden to press the clamp to lift the button. When the CNC car retracts, Do not press the clamp down button in the middle. Flange drill
9. This machine is working, it is forbidden to pass from the front of the safety bar, there is no special circumstances, it is forbidden to lift the front safety bar of the shearing machine, it is absolutely forbidden to pass the safety bar without lifting.
10. The angle of the line in the adjustment of replacement prefix, the word box, punch, die, shear blade, adjust the blade clearance, the guardian must be provided, no person pressing the button.
11. The local hydraulic system (factory) valves have been adjusted, if adjustments need to be adjusted by professionals.
12. The pressure of the hydraulic system should be regularly replaced according to regulations, non-filtered oil into the tank is strictly prohibited.
13. It is forbidden to insert the private tape disk into the drive to avoid bringing the computer virus into the computer.
14. Shear blade, punch die frame, print carriage and moving parts, each time before cleaning with N46 mechanical oil lubrication.
15. Perforated guide rail and screw each class main oil once, the transmission rack and measuring rack and measuring racks to be coated with lubricating grease often lubricated.
16. At get off work, you must cut off the power, clean the equipment dust, clean the venue. Flange drill
